Differences

This shows you the differences between two versions of the page.

--- computers:server:ubuntu10.04lts_hydra [2011/06/26 13:18] – [samba] david
+++ computers:server:ubuntu10.04lts_hydra [2013/09/30 20:29] (current) – [Update] david
@@ Line 41: / Line 41: @@
 </code>
+==== Import ====
+The update repository appears to be broken, so I might need to re-install the OS on hydra.  According to a post I found, all I need to do is "import" the pool.
+  * [[http://forums.freebsd.org/showthread.php?t=16807]] <- a couple posts down
+  * With all drives installed and spun up: <code>
+zpool import
+</code>
+  * Just import your pool now! <code>
+zpool import <poolname>
+</code>
+<code>
+With all of the drives in the system, just run zpool import.
+That will scan all the drives for ZFS metadata, and will show any pools that can be imported.
+Then you just import the one you want via zpool import <poolname>.
+</code>
+==== Update ====
+AH, would make more sense to use a these drive IDs since it would be consistent:
+"You should add your drives using the /dev/disk/by-id directory.  That way the drive will be picked up consistently regardless of the device node in /dev/. "
+==== Drive Failure ====
+  * **2013.09.30** - Looks like we might have had a drive failure.  I know in the past, one of the drives was flaky and would not show up because of a cable issue (swapped cables, and it worked).
+  * Drive identification: (just pasting in the drives in the raid alive<code>
+# status as of today 2013.09.30
+#sudo zpool status -v media
+  pool: media
+ state: DEGRADED
+status: One or more devices could not be opened.  Sufficient replicas exist for
+	the pool to continue functioning in a degraded state.
+action: Attach the missing device and online it using 'zpool online'.
+   see: http://www.sun.com/msg/ZFS-8000-2Q
+ scrub: none requested
+config:
+	NAME        STATE     READ WRITE CKSUM
+	media       DEGRADED     0     0     0
+	  raidz1-0  DEGRADED     0     0     0
+	    sdb     ONLINE       0     0     0
+	    sdc     ONLINE       0     0     0
+	    sdd     ONLINE       0     0     0
+	    sde     ONLINE       0     0     0
+	    sdf     UNAVAIL      0     0     0  cannot open
+errors: No known data errors
+#ls /dev/disk/by-id/ -la
+lrwxrwxrwx 1 root root   9 Sep 30 15:44 scsi-SATA_ST2000DL003-9VT_5YD24VFW -> ../../sde
+lrwxrwxrwx 1 root root   9 Sep 30 15:44 scsi-SATA_ST2000DL003-9VT_5YD2J987 -> ../../sdc
+lrwxrwxrwx 1 root root   9 Sep 30 15:44 scsi-SATA_ST2000DL003-9VT_5YD2K8XW -> ../../sdb
+lrwxrwxrwx 1 root root   9 Sep 30 15:44 scsi-SATA_ST2000DL003-9VT_5YD2K90G -> ../../sdd
+</code>
 ====== Software ======
 ===== Daemons =====
+==== apcd ====
+  - Install **apcupsd** <code>
+sudo apt-get install apcupsd
+</code>
+  - Configure the configuration file:  **/etc/apcupsd/apcupsd.conf** <code>
+UPSTYPE net
+DEVICE xx.xx.xx.xx # your master local apcupsd server
+</code>
+  - Set the **ISCONFIGURED** flag in **/etc/default/apcupsd** to **yes**
+  - Restart the daemon <code>
+sudo service apcupsd restart
+</code>
 ==== LAMP ====
@@ Line 119: / Line 189: @@
 </code>
+==== vsftpd ====
+I would like a local ftp client so that we can move files around as fast as possible
+  - Install **vsftpd** <code>
+sudo apt-get install vsftpd
+</code>
+  - Modify the **/etc/vsftpd.conf** file <code>
+sudo nano /etc/vsftpd.conf
+</code>
+    - Modify so we can write files to the server <code>
+write_enable=YES
+</code>
 ===== Programs =====